This master thesis presents the design and implementation of a GaN-based DC-DC converter for battery module testing, with the objective of replicating arbitrary current profiles on battery modules with a bandwidth of 10 kHz and a current range of ±10 A. The work is motivated by the need to test electric vehicle batteries under realistic dynamic load conditions in a laboratory environment, where high bandwidth and high amplitude current control is essential. To address this challenge, this thesis proposes a solution supported by a complete development flow: system design, hardware development, modeling and controller design, digital controller implementation, and experimental verification. The proposed converter is based on a GaN half-bridge power stage designed with dedicated gate-driving circuitry optimized for a switching frequency of 200 kHz. An LC filter is designed with a cutoff frequency of 10 kHz to meet the target bandwidth. Current sensing and over-current protection functions are integrated on the same PCB. The small-signal model of the power stage is derived, and the PI controller is designed to achieve the desired current loop bandwidth while ensuring stability. The microcontroller implementation and software function principles are presented. Simulation results confirm the validity of the hardware and control design, and experimental tests show that the prototype achieves the intended switching behavior and current-control performance. Step-response and frequency-response tests demonstrate a closed-loop current bandwidth of 10 kHz for amplitudes up to ±10 A. Finally, the drive profile emulation test shows that the proposed converter can closely track the reference battery current and replicate high frequency dynamic patterns featured in the profile.
Questa tesi magistrale presenta la progettazione e l’implementazione di un convertitore DC-DC basato su GaN per il collaudo di moduli batteria, con l’obiettivo di replicare profili di corrente arbitrari sui moduli batteria con una banda passante di 10 kHz e un intervallo di corrente di ±10 A. Il lavoro è motivato dalla necessità di testare batterie per veicoli elettrici in condizioni di carico dinamiche realistiche in un ambiente di laboratorio, in cui è essenziale un controllo di corrente ad alta banda e ad elevata ampiezza. Per affrontare questa sfida, la tesi propone una soluzione supportata da un flusso completo di sviluppo: progettazione del sistema, sviluppo hardware, modellazione e progettazione del controllore, implementazione del controllore digitale e verifica sperimentale. Il convertitore proposto si basa su uno stadio di potenza half-bridge in GaN, progettato con un circuito di pilotaggio dedicato ottimizzato per una frequenza di switching di 200 kHz. È stato progettato un filtro LC con frequenza di taglio pari a 10 kHz, al fine di soddisfare la banda passante target. Le funzioni di misura della corrente e di protezione da sovracorrente sono integrate sullo stesso PCB. È stato derivato il modello a piccoli segnali dello stadio di potenza, e il controllore PI è stato progettato per ottenere la banda passante desiderata dell’anello di corrente garantendo al contempo la stabilità del sistema. Vengono inoltre presentati l’implementazione su microcontrollore e i principi di funzionamento delle principali funzioni software. I risultati di simulazione confermano la validità della progettazione hardware e del controllo, mentre le prove sperimentali mostrano che il prototipo raggiunge il comportamento di switching previsto e le prestazioni desiderate nel controllo di corrente. Le prove di risposta al gradino e di risposta in frequenza dimostrano il raggiungimento di una banda passante dell’anello chiuso di 10 kHz per ampiezze fino a ±10 A. Infine, il test di emulazione del profilo di guida mostra che il convertitore proposto è in grado di seguire da vicino la corrente di riferimento della batteria e di replicare i pattern dinamici ad alta frequenza presenti nel profilo.
Design and implementation of a GaN-based DC-DC converter for battery module testing
Jia, Xining
2025/2026
Abstract
This master thesis presents the design and implementation of a GaN-based DC-DC converter for battery module testing, with the objective of replicating arbitrary current profiles on battery modules with a bandwidth of 10 kHz and a current range of ±10 A. The work is motivated by the need to test electric vehicle batteries under realistic dynamic load conditions in a laboratory environment, where high bandwidth and high amplitude current control is essential. To address this challenge, this thesis proposes a solution supported by a complete development flow: system design, hardware development, modeling and controller design, digital controller implementation, and experimental verification. The proposed converter is based on a GaN half-bridge power stage designed with dedicated gate-driving circuitry optimized for a switching frequency of 200 kHz. An LC filter is designed with a cutoff frequency of 10 kHz to meet the target bandwidth. Current sensing and over-current protection functions are integrated on the same PCB. The small-signal model of the power stage is derived, and the PI controller is designed to achieve the desired current loop bandwidth while ensuring stability. The microcontroller implementation and software function principles are presented. Simulation results confirm the validity of the hardware and control design, and experimental tests show that the prototype achieves the intended switching behavior and current-control performance. Step-response and frequency-response tests demonstrate a closed-loop current bandwidth of 10 kHz for amplitudes up to ±10 A. Finally, the drive profile emulation test shows that the proposed converter can closely track the reference battery current and replicate high frequency dynamic patterns featured in the profile.| File | Dimensione | Formato | |
|---|---|---|---|
|
2026_7_Jia_Thesis_01.pdf
solo utenti autorizzati a partire dal 01/07/2027
Descrizione: Thesis text
Dimensione
6.68 MB
Formato
Adobe PDF
|
6.68 MB | Adobe PDF | Visualizza/Apri |
|
2026_7_Jia_Executive Summary_02.pdf
solo utenti autorizzati a partire dal 01/07/2027
Descrizione: Executive summary of the thesis
Dimensione
3.04 MB
Formato
Adobe PDF
|
3.04 MB | Adobe PDF | Visualizza/Apri |
I documenti in POLITesi sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
https://hdl.handle.net/10589/260527