Proton therapy is an advanced radiotherapy technique that offers highly conformal dose distribution while minimizing irradiation of surrounding healthy tissues. During proton therapy, secondary nuclear interactions may induce activity in patient-relevant tools and devices, producing residual radionuclides that contribute to post-irradiation radioactivity. Among these devices, thermoplastic polycaprolactone (PCL) masks are widely used for patient immobilization. The purpose of this work is to evaluate radionuclides production in an irradiated PCL mask through a combined experimental and computational approach. Measurements were performed on a proton-irradiated mask sample using High-Purity Germanium (HPGe) gamma spectrometry. Detector efficiency calibration and uncertainty evaluation were conducted using the LabSOCS methodology. Attention was devoted to the quantification of Be‑7, identified as the dominant long‑lived activation product through its characteristic 477.6 keV gamma‑ray emission. A detailed Monte Carlo model of the irradiation setup was developed using the FLUKA code. The proton beam was simulated using a Spread-Out Bragg Peak (SOBP) generated from weighted monoenergetic proton beams in the energy range of 90-131 MeV. Residual radionuclide production was scored using the RESNUCLEI card, and the inventories were normalized to a prescribed absorbed dose of 40 Gy to estimate specific activities. The comparison between experimental and simulated results of 0.57 and 1.88 Bq/g, respectively, highlights a discrepancy with a factor of around 3.3, which encouraged a series of sensitivity analyses. These analyses evaluated the impact of material density, thickness, elemental composition, and effective irradiated volume. The results showed that Be-7 production increases with density and thickness and is strongly dependent on carbon content. Carbon was found to be the main contributor to production of Be-7, yielding approximately 2.25 times more Be-7 than oxygen under identical irradiation conditions. Moreover, accounting for the perforated structure of the thermoplastic mask notably reduced the predicted activity, confirming the importance of realistic geometry modelling. The findings of this work contribute to the understanding of activation processes in proton therapy accessories and provide useful information for radiation-protection assessments, waste-management considerations, and future studies of radionuclide production in patient-relevant devices.
La protonterapia rappresenta una tecnica avanzata di radioterapia in grado di garantire una distribuzione della dose altamente conforme, minimizzando al contempo l'irradiazione dei tessuti sani circostanti. Durante il trattamento, le reazioni nucleari secondarie indotte dai protoni possono generare radionuclidi residui nei materiali circostanti, contribuendo alla radioattività residua post-irraggiamento. Tra questi dispositivi, le maschere termoplastiche in policaprolattone (PCL) sono ampiamente utilizzate per l'immobilizzazione del paziente. Lo scopo di questo lavoro consiste nel valutare la produzione di radionuclidi in una maschera in PCL irradiata mediante un approccio combinato sperimentale e computazionale. Le misure di caratterizzazione sono state effettuate mediante spettrometria gamma tramite rivelatore al germanio iperpuro (HPGe). La calibrazione dell'efficienza del rivelatore e la valutazione delle incertezze sono state eseguite mediante la metodologia LabSOCS. Particolare attenzione è stata dedicata alla quantificazione del Be-7, identificato come il principale prodotto di attivazione a lunga vita grazie alla caratteristica emissione gamma a 477.6 keV. È stato sviluppato un modello Monte Carlo dettagliato della configurazione di irraggiamento utilizzando il codice FLUKA. Il fascio di protoni è stato simulato mediante un picco di Bragg modulato (Spread-Out Bragg Peak, SOBP) ottenuto dalla sovrapposizione di fasci monoenergetici pesati nell'intervallo energetico compreso tra 90 e 131 MeV. La produzione dei radionuclidi residui è stata valutata mediante la card RESNUCLEI e gli inventari ottenuti sono stati normalizzati ad una dose assorbita prescritta di 40 Gy al fine di stimare le attività specifiche. Il confronto tra i risultati sperimentali (0.57 Bq/g) e quelli simulati (1.88 Bq/g) ha evidenziato una discrepanza di circa 3.3, che ha motivato l'esecuzione di una serie di analisi di sensibilità. Tali analisi hanno permesso di valutare l'influenza della densità del materiale, dello spessore, della composizione elementare e del volume effettivamente irradiato. I risultati hanno mostrato che la produzione di Be-7 aumenta all'aumentare della densità e dello spessore ed è fortemente dipendente dal contenuto di carbonio. In particolare, il carbonio è risultato essere il principale contributore alla produzione di Be-7, producendo circa 2.25 volte più Be-7 rispetto all'ossigeno in condizioni identiche di irraggiamento. Inoltre, la considerazione della struttura perforata della maschera termoplastica ha comportato una riduzione significativa dell'attività prevista, confermando l'importanza di una modellazione geometrica realistica. I risultati ottenuti contribuiscono a una migliore comprensione dei processi di attivazione negli accessori utilizzati in protonterapia e forniscono informazioni utili per le valutazioni di radioprotezione, le considerazioni relative alla gestione dei rifiuti radioattivi e i futuri studi sulla produzione di radionuclidi nei dispositivi impiegati sul paziente.
Numerical and experimental characterization of activated patient masks in Proton Therapy
RODAINA ALI MOHAMED ALI
2025/2026
Abstract
Proton therapy is an advanced radiotherapy technique that offers highly conformal dose distribution while minimizing irradiation of surrounding healthy tissues. During proton therapy, secondary nuclear interactions may induce activity in patient-relevant tools and devices, producing residual radionuclides that contribute to post-irradiation radioactivity. Among these devices, thermoplastic polycaprolactone (PCL) masks are widely used for patient immobilization. The purpose of this work is to evaluate radionuclides production in an irradiated PCL mask through a combined experimental and computational approach. Measurements were performed on a proton-irradiated mask sample using High-Purity Germanium (HPGe) gamma spectrometry. Detector efficiency calibration and uncertainty evaluation were conducted using the LabSOCS methodology. Attention was devoted to the quantification of Be‑7, identified as the dominant long‑lived activation product through its characteristic 477.6 keV gamma‑ray emission. A detailed Monte Carlo model of the irradiation setup was developed using the FLUKA code. The proton beam was simulated using a Spread-Out Bragg Peak (SOBP) generated from weighted monoenergetic proton beams in the energy range of 90-131 MeV. Residual radionuclide production was scored using the RESNUCLEI card, and the inventories were normalized to a prescribed absorbed dose of 40 Gy to estimate specific activities. The comparison between experimental and simulated results of 0.57 and 1.88 Bq/g, respectively, highlights a discrepancy with a factor of around 3.3, which encouraged a series of sensitivity analyses. These analyses evaluated the impact of material density, thickness, elemental composition, and effective irradiated volume. The results showed that Be-7 production increases with density and thickness and is strongly dependent on carbon content. Carbon was found to be the main contributor to production of Be-7, yielding approximately 2.25 times more Be-7 than oxygen under identical irradiation conditions. Moreover, accounting for the perforated structure of the thermoplastic mask notably reduced the predicted activity, confirming the importance of realistic geometry modelling. The findings of this work contribute to the understanding of activation processes in proton therapy accessories and provide useful information for radiation-protection assessments, waste-management considerations, and future studies of radionuclide production in patient-relevant devices.| File | Dimensione | Formato | |
|---|---|---|---|
|
2026_07_Ali Mohamed Ali_Executive Summary_02.pdf
non accessibile
Descrizione: Executive Summary
Dimensione
939.17 kB
Formato
Adobe PDF
|
939.17 kB | Adobe PDF | Visualizza/Apri |
|
2026_07_Ali Mohamed Ali_Thesis_01.pdf
non accessibile
Descrizione: Thesis text
Dimensione
1.91 MB
Formato
Adobe PDF
|
1.91 MB | Adobe PDF | Visualizza/Apri |
I documenti in POLITesi sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
https://hdl.handle.net/10589/260783