This thesis investigates the feasibility of replacing a conventional bolted fastening system with blind rivets in a structural steel joint through finite element analyses. Following a review of the state of the art on bolted and riveted joints, numerical models were developed in Abaqus to compare the structural response of the two fastening solutions, while keeping unchanged the joint geometry and loading conditions. The analyses began with the validation of the adopted material and damage models through numerical simulations of tensile tests available in the literature and through the comparison of the simulated rivet setting response with the installation data provided by the rivet manufacturer. Subsequently, finite element models of both the bolted and riveted joints were developed, including bolt preload and the simulation of the blind-rivet setting process. The structural behaviour of the two configurations was compared in terms of displacement, stress distribution and equivalent plastic strain (PEEQ). The results show that the riveted configuration exhibits a moderate reduction in stiffness, corresponding to an increase in maximum displacement of approximately 10.5 % compared with the baseline bolted solution. Nevertheless, the riveted joint is capable of sustaining the prescribed loading conditions without exhibiting failure mechanisms, demonstrating the technical feasibility of the proposed solution. Although further experimental and numerical investigations may be required, particularly for a more accurate characterization of the rivet materials, the study highlights the potential of blind rivets as an attractive alternative to bolts in structural applications.
La presente tesi esamina la fattibilità della sostituzione di un sistema di fissaggio convenzionale con bulloni, con rivetti ciechi in un giunto strutturale in acciaio, mediante analisi agli elementi finiti. A seguito di una revisione dello stato dell’arte sui giunti bullonati e rivettati, sono stati sviluppati modelli numerici in Abaqus per confrontare la risposta strutturale delle due soluzioni di fissaggio, mantenendo inalterata la geometria del giunto e le condizioni di carico. Le analisi sono iniziate con la validazione dei modelli di materiale e di danneggiamento adottati attraverso simulazioni numeriche di prove di trazione disponibili in letteratura e attraverso il confronto della risposta simulata di installazione dei rivetti con i dati di forniti dal produttore dei rivetti. Successivamente, sono stati sviluppati modelli agli elementi finiti del giunto bullonato e del giunto rivettato, includendo il precarico dei bulloni e la simulazione del processo di installazione dei rivetti ciechi. Il comportamento strutturale delle due configurazioni è stato confrontato in termini di spostamento, distribuzione delle sollecitazioni e deformazione plastica equivalente (PEEQ). I risultati mostrano che la configurazione rivettata presenta una moderata riduzione della rigidità, corrispondente a un aumento dello spostamento massimo di circa il 10.5 % rispetto alla soluzione di riferimento bullonata. Ciononostante, il giunto rivettato è in grado di sostenere le condizioni di carico prescritte senza presentare meccanismi di rottura, dimostrando la fattibilità tecnica della soluzione proposta. Sebbene possano essere necessarie ulteriori indagini sperimentali e numeriche, in particolare per una caratterizzazione più accurata dei materiali dei rivetti, lo studio evidenzia il potenziale dei rivetti ciechi come valida alternativa ai bulloni in applicazioni strutturali.
Finite element assessment of blind rivets as an alternative to bolted fastening in structural steel connections
Fago Mastrangelo, Carmine
2025/2026
Abstract
This thesis investigates the feasibility of replacing a conventional bolted fastening system with blind rivets in a structural steel joint through finite element analyses. Following a review of the state of the art on bolted and riveted joints, numerical models were developed in Abaqus to compare the structural response of the two fastening solutions, while keeping unchanged the joint geometry and loading conditions. The analyses began with the validation of the adopted material and damage models through numerical simulations of tensile tests available in the literature and through the comparison of the simulated rivet setting response with the installation data provided by the rivet manufacturer. Subsequently, finite element models of both the bolted and riveted joints were developed, including bolt preload and the simulation of the blind-rivet setting process. The structural behaviour of the two configurations was compared in terms of displacement, stress distribution and equivalent plastic strain (PEEQ). The results show that the riveted configuration exhibits a moderate reduction in stiffness, corresponding to an increase in maximum displacement of approximately 10.5 % compared with the baseline bolted solution. Nevertheless, the riveted joint is capable of sustaining the prescribed loading conditions without exhibiting failure mechanisms, demonstrating the technical feasibility of the proposed solution. Although further experimental and numerical investigations may be required, particularly for a more accurate characterization of the rivet materials, the study highlights the potential of blind rivets as an attractive alternative to bolts in structural applications.| File | Dimensione | Formato | |
|---|---|---|---|
|
2026_07_Fago_Mastrangelo_Tesi.pdf
accessibile in internet per tutti
Descrizione: Testo della tesi
Dimensione
11.64 MB
Formato
Adobe PDF
|
11.64 MB | Adobe PDF | Visualizza/Apri |
|
2026_07_Fago_Mastrangelo_Executive_Summary.pdf
accessibile in internet per tutti
Descrizione: Testo dell'executive summary
Dimensione
3.53 MB
Formato
Adobe PDF
|
3.53 MB | Adobe PDF | Visualizza/Apri |
I documenti in POLITesi sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
https://hdl.handle.net/10589/261140