This thesis addresses the position control of a double-acting pneumatic cylinder developed in collaboration with Camozzi Automation. The baseline configuration consists of a PID controller that regulates the pressure of a single chamber while keeping the opposite chamber at constant supply pressure. In the presence of significant stick-slip friction, the interaction between the PID integral term and the stiction characteristic generates persistent limit cycles near the target position, preventing accurate and smooth steady-state tracking. To overcome these limitations, a Sliding Mode Control (SMC) framework is proposed, actively regulating the pressure in both chambers simultaneously through Camozzi Open Frame proportional valves. SMC was selected for its inherent robustness to model uncertainties and external disturbances, a critical advantage in pneumatic systems where friction is the dominant and most difficult to model source of uncertainty. Deliberately keeping the system model simple, the robustness of SMC is exploited to compensate for unmodeled friction effects without complex identification procedures. A central contribution of this work is a MISO-to-SISO reformulation of the control problem: the SMC controller computes a single virtual input (the net desired pneumatic force) while an input allocation algorithm maps this force to the individual pressure setpoints of the two valves. Three different SMC strategies have been designed, implemented, and experimentally validated. Experimental results demonstrate that all SMC variants significantly outperform the PID, eliminating stick-slip-induced limit cycles and achieving superior tracking performance.
Questa tesi affronta il controllo di posizione di un cilindro pneumatico a doppio effetto sviluppato in collaborazione con Camozzi Automation. La configurazione di partenza consiste in un controllore PID che regola la pressione di una singola camera, mantenendo la camera opposta a pressione di alimentazione costante. In presenza di un significativo attrito di tipo stick-slip, l’interazione tra il termine integrale del PID e la caratteristica di stiction genera cicli limite persistenti in prossimità della posizione desiderata, impedendo un inseguimento accurato e regolare in regime stazionario. Per superare tali limitazioni, viene proposto un approccio basato su Sliding Mode Control (SMC), in cui la pressione di entrambe le camere viene regolata attivamente e simultaneamente mediante valvole proporzionali Camozzi Open Frame. Lo SMC è stato scelto per la sua intrinseca robustezza rispetto alle incertezze di modello e ai disturbi esterni, una caratteristica particolarmente vantaggiosa nei sistemi pneumatici, nei quali l’attrito rappresenta la principale e più difficile sorgente di incertezza da modellare. Mantenendo deliberatamente semplice il modello del sistema, la robustezza dello SMC viene sfruttata per compensare gli effetti di attrito non modellati, evitando procedure di identificazione complesse. Un contributo centrale di questo lavoro è la riformulazione del problema di controllo da MISO a SISO: il controllore SMC calcola un singolo ingresso virtuale, corrispondente alla forza pneumatica desiderata, mentre un algoritmo di input allocation mappa tale forza nei singoli riferimenti di pressione delle due valvole. Tre diverse strategie SMC sono state progettate, implementate e validate sperimentalmente. I risultati sperimentali dimostrano che tutte le varianti SMC superano significativamente le prestazioni del PID, eliminando i cicli limite indotti dallo stick-slip e ottenendo migliori prestazioni di inseguimento.
Force-based sliding mode position control of a double-acting pneumatic cylinder with dual-chamber pressure regulation
CAMPANA, CHRISTIAN
2025/2026
Abstract
This thesis addresses the position control of a double-acting pneumatic cylinder developed in collaboration with Camozzi Automation. The baseline configuration consists of a PID controller that regulates the pressure of a single chamber while keeping the opposite chamber at constant supply pressure. In the presence of significant stick-slip friction, the interaction between the PID integral term and the stiction characteristic generates persistent limit cycles near the target position, preventing accurate and smooth steady-state tracking. To overcome these limitations, a Sliding Mode Control (SMC) framework is proposed, actively regulating the pressure in both chambers simultaneously through Camozzi Open Frame proportional valves. SMC was selected for its inherent robustness to model uncertainties and external disturbances, a critical advantage in pneumatic systems where friction is the dominant and most difficult to model source of uncertainty. Deliberately keeping the system model simple, the robustness of SMC is exploited to compensate for unmodeled friction effects without complex identification procedures. A central contribution of this work is a MISO-to-SISO reformulation of the control problem: the SMC controller computes a single virtual input (the net desired pneumatic force) while an input allocation algorithm maps this force to the individual pressure setpoints of the two valves. Three different SMC strategies have been designed, implemented, and experimentally validated. Experimental results demonstrate that all SMC variants significantly outperform the PID, eliminating stick-slip-induced limit cycles and achieving superior tracking performance.| File | Dimensione | Formato | |
|---|---|---|---|
|
2026_07_Campana_Executive Summary.pdf
non accessibile
Descrizione: Executive Summary
Dimensione
739.53 kB
Formato
Adobe PDF
|
739.53 kB | Adobe PDF | Visualizza/Apri |
|
2026_07_Campana_Tesi.pdf
non accessibile
Descrizione: Tesi
Dimensione
12.5 MB
Formato
Adobe PDF
|
12.5 MB | Adobe PDF | Visualizza/Apri |
I documenti in POLITesi sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
https://hdl.handle.net/10589/261597