The objective of this research is to investigate the impact of ice accretion on the aerody namic performance of a blended wing body UAV model. The ice shapes were generated through deterministic and semi-stochastic approaches within the PoliMIce ice accretion software suite, and then 3D-printed and mounted on the leading edge of the wing model.The experimental campaign was conducted in the Sergio De Ponte closed-circuit wind tunnel at Politecnico di Milano. Aerodynamic loads were measured using an external multi-axis force balance over a range of angles of attack from −8◦to 16◦ at Re = 1.3×105and Re = 3.2 × 105. Results showed that increasing the Reynolds number improved the overall performance by increasing lift, delaying stall and decreasing drag. Among all the artificial ice shapes, the deterministic glaze ice characterized by double-horn structures(ice shape of ID:v120T-12) induced the most critical performance degradation; the maxi mum lift coefficient was reduced by 35%, and range and endurance capabilities dropped by 50% compared to the baseline UAV model. Furthermore, the results demonstrated thatthe semi-stochastic ice shapes produced better aerodynamic performance than their deter ministic counterparts. The three-dimensional irregularities of the semi-stochastic models triggered a premature laminar-to-turbulent transition, leading to a more energized bound ary layer, delaying flow separation, and lowering the pressure drag. Moreover, surface flow visualization, performed to map skin friction lines as a valuable support for the experi mental data, demonstrated the presence and evolution of the laminar separation bubble(LSB) over the clean model, while the selected iced configurations suppressed the LSB,promoting an earlier onset of flow separation.

L’obiettivo di questa ricerca è studiare l’impatto dell’accumulo di ghiaccio sulle prestazioni aerodinamiche di un modello drone a fusoliera integrata. Le forme di ghiaccio sono stategenerate attraverso approcci deterministici e semi-stocastici tramite il software di accresci mento di ghiaccio PoliMIce, per poi essere stampate in 3D e montate sul bordo d’attaccodel modello. La campagna sperimentale è stata condotta nella galleria del vento subson ica a circuito chiuso Sergio De Ponte del Politecnico di Milano. I carichi aerodinamicisono stati misurati tramite una bilancia esterna multiassiale su un intervallo di angoli diincidenza compreso tra −8◦e 16◦ a Re = 1.3 × 105e Re = 3.2 × 105. I risultati hanno mostrato che l’aumento del numero di Reynolds migliora le prestazioni complessive incre mentando la portanza, ritardando lo stallo e riducendo la resistenza aerodinamica.Tra tutte le forme di ghiaccio artificiali, il glaze deterministico caratterizzato da strutturea doppio corno (forma di ghiaccio v120T-12) ha indotto il degrado delle prestazioni piùcritico; il coefficiente di portanza si è ridotto del 35% e le capacità di autonomia e di per manenza in volo sono crollate del 50% rispetto al modello drone senza ghiaccio. Inoltre, irisultati hanno mostrato che le forme di ghiaccio semi-stocastiche producono prestazioniaerodinamiche migliori rispetto alle loro controparti deterministiche. Le irregolarità tridi mensionali proprie dei modelli semi-stocastici innescano una transizione prematura delflusso da laminare a turbolento, portando a uno strato limite più energizzato, ritardandoquindi la separazione del flusso e riducendo la resistenza di pressione. In aggiunta, lavisualizzazione del flusso superficiale, eseguita per mappare le linee di attrito come validosupporto ai dati sperimentali, ha mostrato la presenza e l’evoluzione della bolla di sepa razione laminare (LSB) sul modello pulito, mentre le forme di ghiaccio selezionate hanno soppresso la bolla e favorito la separazione prematura del flusso.

Experimental study of the aerodynamic performance at low Reynolds number UAV model with artificial ice shapes

Cammaroto, Giovanni Gualberto
2025/2026

Abstract

The objective of this research is to investigate the impact of ice accretion on the aerody namic performance of a blended wing body UAV model. The ice shapes were generated through deterministic and semi-stochastic approaches within the PoliMIce ice accretion software suite, and then 3D-printed and mounted on the leading edge of the wing model.The experimental campaign was conducted in the Sergio De Ponte closed-circuit wind tunnel at Politecnico di Milano. Aerodynamic loads were measured using an external multi-axis force balance over a range of angles of attack from −8◦to 16◦ at Re = 1.3×105and Re = 3.2 × 105. Results showed that increasing the Reynolds number improved the overall performance by increasing lift, delaying stall and decreasing drag. Among all the artificial ice shapes, the deterministic glaze ice characterized by double-horn structures(ice shape of ID:v120T-12) induced the most critical performance degradation; the maxi mum lift coefficient was reduced by 35%, and range and endurance capabilities dropped by 50% compared to the baseline UAV model. Furthermore, the results demonstrated thatthe semi-stochastic ice shapes produced better aerodynamic performance than their deter ministic counterparts. The three-dimensional irregularities of the semi-stochastic models triggered a premature laminar-to-turbulent transition, leading to a more energized bound ary layer, delaying flow separation, and lowering the pressure drag. Moreover, surface flow visualization, performed to map skin friction lines as a valuable support for the experi mental data, demonstrated the presence and evolution of the laminar separation bubble(LSB) over the clean model, while the selected iced configurations suppressed the LSB,promoting an earlier onset of flow separation.
ING - Scuola di Ingegneria Industriale e dell'Informazione
22-lug-2026
2025/2026
L’obiettivo di questa ricerca è studiare l’impatto dell’accumulo di ghiaccio sulle prestazioni aerodinamiche di un modello drone a fusoliera integrata. Le forme di ghiaccio sono stategenerate attraverso approcci deterministici e semi-stocastici tramite il software di accresci mento di ghiaccio PoliMIce, per poi essere stampate in 3D e montate sul bordo d’attaccodel modello. La campagna sperimentale è stata condotta nella galleria del vento subson ica a circuito chiuso Sergio De Ponte del Politecnico di Milano. I carichi aerodinamicisono stati misurati tramite una bilancia esterna multiassiale su un intervallo di angoli diincidenza compreso tra −8◦e 16◦ a Re = 1.3 × 105e Re = 3.2 × 105. I risultati hanno mostrato che l’aumento del numero di Reynolds migliora le prestazioni complessive incre mentando la portanza, ritardando lo stallo e riducendo la resistenza aerodinamica.Tra tutte le forme di ghiaccio artificiali, il glaze deterministico caratterizzato da strutturea doppio corno (forma di ghiaccio v120T-12) ha indotto il degrado delle prestazioni piùcritico; il coefficiente di portanza si è ridotto del 35% e le capacità di autonomia e di per manenza in volo sono crollate del 50% rispetto al modello drone senza ghiaccio. Inoltre, irisultati hanno mostrato che le forme di ghiaccio semi-stocastiche producono prestazioniaerodinamiche migliori rispetto alle loro controparti deterministiche. Le irregolarità tridi mensionali proprie dei modelli semi-stocastici innescano una transizione prematura delflusso da laminare a turbolento, portando a uno strato limite più energizzato, ritardandoquindi la separazione del flusso e riducendo la resistenza di pressione. In aggiunta, lavisualizzazione del flusso superficiale, eseguita per mappare le linee di attrito come validosupporto ai dati sperimentali, ha mostrato la presenza e l’evoluzione della bolla di sepa razione laminare (LSB) sul modello pulito, mentre le forme di ghiaccio selezionate hanno soppresso la bolla e favorito la separazione prematura del flusso.
File allegati
File Dimensione Formato  
2026_07_Cammaroto.pdf

accessibile in internet solo dagli utenti autorizzati

Dimensione 60.91 MB
Formato Adobe PDF
60.91 MB Adobe PDF   Visualizza/Apri

I documenti in POLITesi sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/10589/261607