Molecular diagnostic systems based on real-time PCR are increasingly being developed in integrated point-of-care formats, with the aim of performing complex analytical workflows closer to the patient and with less dependence on centralized laboratory infrastructure. To make this possible, operations that are normally carried out separately in the laboratory, including sample preparation, nucleic-acid extraction, reagent handling, liquid transfer, amplification and fluorescence detection, must be coordinated within the same automated platform. DiaxxoCare is one example of this type of system. It integrates nucleic-acid extraction with real-time PCR amplification and detection in an automated workflow designed for point-of care molecular testing. In such a system, however, increasing automation also means that operations previously performed and visually supervised by a laboratory operator must be carried out and monitored by the instrument itself. Automated liquid transfer is one of these critical operations. The purified nucleic-acid solution and other protocol liquids must be aspirated, transported and dispensed between physically separated parts of the system before the PCR reaction can be performed. In an air-displacement pipetting system, however, correct execution of the commanded plunger motion does not necessarily guarantee that the intended physical transfer has occurred as expected. Conditions such as internal air bubbles, insufficient liquid, leakage, incorrect tip positioning or incomplete droplet detachment can alter the transfer without being fully described by the actuator command alone. This thesis investigates whether pressure-related signals acquired during automated pipet ting can provide additional information about these individual transfer events. Pressure was selected as the main observable process parameter because, in an air-displacement sys tem, it reflects the interaction between plunger motion, the compressible air cushion, the liquid and the conditions at the tip outlet. It can therefore provide information about trans fer behaviour while remaining compatible with the existing pipetting architecture. At the same time, pressure remains an indirect signal and is not treated as a direct measurement of deposited volume. The experimental work first characterized pressure traces acquired under defined nominal conditions and used them to construct configuration-specific reference profiles. Represen tative non-nominal conditions were then reproduced experimentally, including internal air bubbles, pre-dispense droplets, insufficient liquid and changes in tip position. Whenever possible, the resulting pressure traces were associated with independent physical evidence obtained from direct observation, images or gravimetric measurements. Individual dispensing events were reconstructed from the recorded pressure streams and metadata, represented on a common temporal grid and compared with the correspond ing nominal reference. Different comparison strategies were investigated during method development, including full-trace and windowed similarity measures and limited temporal alignment. The final assessment combines the main dispense-pressure trace with comple i mentary checks, including maximum dispense pressure and, when available, a post-dispense pickup signal related to residual liquid at the tip. The method was integrated into the experimental machine workflow through P1590 for reference generation and PCK1600 for event-level quality-control assessment. For each analysed transfer, the available KPI values and decision states are stored and combined into an overall SUCCESS, CAUTION or WARNING status. Pressure-derived outputs are kept separate from independent physical observations so that the behaviour of the method can be evaluated against experimental evidence. The work therefore develops and experimentally evaluates a pressure-based quality-control approach for automated liquid transfer in diaxxoCare. The diaxxo Liquid Station is consid ered separately because of its different geometry and dispensing dynamics. The proposed method is not intended to replace direct volumetric verification, but to provide an embed ded and traceable indication of whether an individual transfer behaves consistently with the expected nominal process.
I sistemi di diagnostica molecolare basati sulla PCR in tempo reale vengono sempre più sviluppati in formati integrati point-of-care, con l’obiettivo di eseguire workflow analitici complessi più vicino al paziente e ridurre la dipendenza da infrastrutture di laboratorio centralizzate. Per rendere possibile questo tipo di utilizzo, operazioni che normalmente ven gono eseguite separatamente in laboratorio, tra cui preparazione del campione, estrazione degli acidi nucleici, gestione dei reagenti, trasferimento dei liquidi, amplificazione e ril evazione della fluorescenza, devono essere coordinate all’interno della stessa piattaforma automatizzata. DiaxxoCare rappresenta un esempio di questo tipo di sistema. La piattaforma integra l’estrazione degli acidi nucleici con l’amplificazione e la rilevazione mediante PCR in tempo reale in un workflow automatizzato pensato per la diagnostica molecolare point-of-care. In un sistema di questo tipo, però, un livello maggiore di automazione significa anche che operazioni che in laboratorio sarebbero eseguite e controllate visivamente da un operatore devono essere svolte e monitorate direttamente dallo strumento. Il trasferimento automatizzato dei liquidi è una di queste operazioni critiche. La soluzione contenente gli acidi nucleici purificati e gli altri liquidi previsti dal protocollo devono essere aspirati, trasportati e dispensati tra regioni fisicamente separate del sistema prima che possa avvenire la reazione PCR. In un sistema di pipettaggio air-displacement, tuttavia, la corretta esecuzione del movimento comandato del pistone non garantisce necessariamente che il trasferimento fisico sia avvenuto come previsto. Condizioni come bolle d’aria interne, quantità insufficiente di liquido, perdite, un posizionamento errato della tip o un distacco incompleto della goccia possono modificare il trasferimento senza essere completamente descritte dal solo comando dell’attuatore. Questa tesi studia quindi se i segnali legati alla pressione, acquisiti durante il pipettaggio automatizzato, possano fornire informazioni aggiuntive sui singoli eventi di trasferimento. La pressione è stata scelta come principale parametro osservabile di processo perché, in un sistema air-displacement, riflette l’interazione tra movimento del pistone, cuscino d’aria comprimibile, liquido e condizioni presenti all’uscita della tip. Può quindi fornire infor mazioni sul comportamento del trasferimento rimanendo compatibile con l’architettura di pipettaggio esistente. La pressione resta comunque un segnale indiretto e non viene interpretata come una misura diretta del volume depositato. Il lavoro sperimentale si è inizialmente concentrato sulla caratterizzazione delle tracce di pressione acquisite in condizioni nominali definite, utilizzate successivamente per costruire profili di riferimento specifici della configurazione. Sono state poi riprodotte sperimen talmente condizioni non nominali rappresentative, tra cui bolle d’aria interne, gocce pre dispense, quantità insufficiente di liquido e variazioni della posizione della tip. Quando possibile, le corrispondenti tracce di pressione sono state associate a evidenze fisiche in dipendenti ottenute mediante osservazione diretta, immagini o misure gravimetriche. I singoli eventi di dispensazione sono stati ricostruiti a partire dagli stream di pressione registrati e dai relativi metadata, riportati su una griglia temporale comune e confrontati con la reference nominale corrispondente. Durante lo sviluppo sono state analizzate di verse strategie di confronto, tra cui misure di similarità sull’intera traccia o su finestre temporali selezionate e un allineamento temporale limitato. La valutazione finale combina la traccia principale di pressione durante il dispense con controlli complementari, tra cui la pressione massima e, quando disponibile, un segnale post-dispense pickup legato alla possibile presenza di liquido residuo alla tip. Il metodo è stato integrato nel workflow sperimentale della macchina attraverso P1590 per la generazione delle reference e PCK1600 per la valutazione di quality control a livello del singolo evento. Per ogni trasferimento analizzato vengono conservati i valori dei KPI disponibili e i relativi stati decisionali, successivamente combinati in uno stato complessivo SUCCESS, CAUTION o WARNING.Irisultati derivati dalla pressione vengono mantenuti separati dalle osservazioni fisiche indipendenti, in modo da poter valutare il comportamento del metodo rispetto all’evidenza sperimentale. Il lavoro sviluppa e valuta quindi sperimentalmente un approccio di quality control basato sulla pressione per il trasferimento automatizzato dei liquidi in diaxxoCare. La diaxxo Liquid Station viene considerata separatamente a causa della diversa geometria e delle differenti dinamiche di dispensazione. Il metodo proposto non ha lo scopo di sostituire una verifica volumetrica diretta, ma di fornire un’indicazione integrata e tracciabile della compatibilità del singolo trasferimento con il comportamento nominale atteso.
Development and experimental evaluation of a pressure-based quality control system for automated liquid dispensing in point-of-care molecular diagnostics
ONETTI, MARTINA
2025/2026
Abstract
Molecular diagnostic systems based on real-time PCR are increasingly being developed in integrated point-of-care formats, with the aim of performing complex analytical workflows closer to the patient and with less dependence on centralized laboratory infrastructure. To make this possible, operations that are normally carried out separately in the laboratory, including sample preparation, nucleic-acid extraction, reagent handling, liquid transfer, amplification and fluorescence detection, must be coordinated within the same automated platform. DiaxxoCare is one example of this type of system. It integrates nucleic-acid extraction with real-time PCR amplification and detection in an automated workflow designed for point-of care molecular testing. In such a system, however, increasing automation also means that operations previously performed and visually supervised by a laboratory operator must be carried out and monitored by the instrument itself. Automated liquid transfer is one of these critical operations. The purified nucleic-acid solution and other protocol liquids must be aspirated, transported and dispensed between physically separated parts of the system before the PCR reaction can be performed. In an air-displacement pipetting system, however, correct execution of the commanded plunger motion does not necessarily guarantee that the intended physical transfer has occurred as expected. Conditions such as internal air bubbles, insufficient liquid, leakage, incorrect tip positioning or incomplete droplet detachment can alter the transfer without being fully described by the actuator command alone. This thesis investigates whether pressure-related signals acquired during automated pipet ting can provide additional information about these individual transfer events. Pressure was selected as the main observable process parameter because, in an air-displacement sys tem, it reflects the interaction between plunger motion, the compressible air cushion, the liquid and the conditions at the tip outlet. It can therefore provide information about trans fer behaviour while remaining compatible with the existing pipetting architecture. At the same time, pressure remains an indirect signal and is not treated as a direct measurement of deposited volume. The experimental work first characterized pressure traces acquired under defined nominal conditions and used them to construct configuration-specific reference profiles. Represen tative non-nominal conditions were then reproduced experimentally, including internal air bubbles, pre-dispense droplets, insufficient liquid and changes in tip position. Whenever possible, the resulting pressure traces were associated with independent physical evidence obtained from direct observation, images or gravimetric measurements. Individual dispensing events were reconstructed from the recorded pressure streams and metadata, represented on a common temporal grid and compared with the correspond ing nominal reference. Different comparison strategies were investigated during method development, including full-trace and windowed similarity measures and limited temporal alignment. The final assessment combines the main dispense-pressure trace with comple i mentary checks, including maximum dispense pressure and, when available, a post-dispense pickup signal related to residual liquid at the tip. The method was integrated into the experimental machine workflow through P1590 for reference generation and PCK1600 for event-level quality-control assessment. For each analysed transfer, the available KPI values and decision states are stored and combined into an overall SUCCESS, CAUTION or WARNING status. Pressure-derived outputs are kept separate from independent physical observations so that the behaviour of the method can be evaluated against experimental evidence. The work therefore develops and experimentally evaluates a pressure-based quality-control approach for automated liquid transfer in diaxxoCare. The diaxxo Liquid Station is consid ered separately because of its different geometry and dispensing dynamics. The proposed method is not intended to replace direct volumetric verification, but to provide an embed ded and traceable indication of whether an individual transfer behaves consistently with the expected nominal process.| File | Dimensione | Formato | |
|---|---|---|---|
|
2026_10_Onetti.pdf
accessibile in internet per tutti
Dimensione
19.02 MB
Formato
Adobe PDF
|
19.02 MB | Adobe PDF | Visualizza/Apri |
|
Executive_Summary_Onetti_EN_IT.pdf
accessibile in internet per tutti
Descrizione: Executive Summary
Dimensione
65.45 kB
Formato
Adobe PDF
|
65.45 kB | Adobe PDF | Visualizza/Apri |
I documenti in POLITesi sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
https://hdl.handle.net/10589/266292