Copper components are typically joined using welding or torch and induction brazing. However, both of these methods rely on extensive and poorly localised heating, which spreads through copper's high thermal conductivity. This can cause grain growth, distortion and mechanical degradation near the joint. This thesis investigates laser brazing as an alternative that can produce metallurgically sound copper-to-copper lap joints (“sandwich” configuration) without melting the base material. The aim is to establish laser brazing as a genuine competitor to conventional techniques. Two filler forms (brazing paste and rod) were tested using two laser sources with different absorption properties in copper (near-infrared fibre and blue lasers). The following parameters were explored: power, exposure time, wobbling geometry, beam shaping, and clamping and surface preparation. Initial process exploration relied on qualitative analysis and visual inspection of the joints. Cross-sectional analysis, chemical etching and tensile testing were then applied to the most promising conditions. Brazing paste was found to be unsuitable as copper's conductivity drew away heat faster than it could be supplied, resulting in the lower sheet being starved of heat, while increasing the power merely damaged the upper plate. Brazing rod, by contrast, produced complete, low-porosity joints over a wide process window, especially with the near- infrared (NIR) laser. Tensile tests on selected rod-brazed specimens showed consistent peak stresses of 220-231 MPa, with fracture occurring outside the joint. This confirms that the strength matches or exceeds that of the base material. Thermal simulations, calibrated against thermosensitive sticker measurements, corroborated these results.
I componenti in rame vengono solitamente uniti mediante saldatura o brasatura a fiamma o a induzione. Tuttavia, entrambi questi metodi si basano su un riscaldamento estesa e scarsamente localizzato, che si diffonde a causa dell'elevata conduttività termica del rame, causando crescita dei grani, deformazioni e degrado meccanico in prossimità del giunto. La presente tesi studia la brasatura laser come alternativa in grado di produrre giunti sovrapposti rame-rame (configurazione "a sandwich") metallurgicamente validi senza fondere il materiale di base, con l'obiettivo di affermarla come valida alternativa alle tecniche convenzionali. Sono state testate due forme di materiale d'apporto (pasta e bacchetta per brasatura) con due sorgenti laser aventi diverse proprietà di assorbimento nel rame (fibra nel vicino infrarosso e laser blu), esaminando potenza, tempo di esposizione, geometria dell'oscillazione, modellazione del fascio, serraggio e preparazione della superficie. L'esplorazione iniziale del processo si è basata su analisi qualitative e ispezioni visive dei giunti; alle condizioni più promettenti sono state poi applicate analisi trasversali, incisione chimica e prove di trazione. La pasta si è rivelata inadatta: la conduttività del rame dissipava il calore più rapidamente di quanto potesse essere fornito, privando la lamiera inferiore del calore necessario, mentre l'aumento della potenza danneggiava semplicemente la lamiera superiore. La bacchetta, al contrario, ha prodotto giunti completi e a bassa porosità in un ampio intervallo di condizioni, specialmente con il laser NIR. Le prove di trazione su provini selezionati hanno evidenziato sollecitazioni di picco costanti tra 220 e 231 MPa, con rottura fuori dal giunto, confermando resistenza pari o superiore al materiale base. Le simulazioni termiche, calibrate su misurazioni con adesivi termosensibili, hanno confermato questi risultati.
Process development for industrial application of copper laser brazing using paste and rod filler materials for high-strength lap joints
LABATE, GRETA
2025/2026
Abstract
Copper components are typically joined using welding or torch and induction brazing. However, both of these methods rely on extensive and poorly localised heating, which spreads through copper's high thermal conductivity. This can cause grain growth, distortion and mechanical degradation near the joint. This thesis investigates laser brazing as an alternative that can produce metallurgically sound copper-to-copper lap joints (“sandwich” configuration) without melting the base material. The aim is to establish laser brazing as a genuine competitor to conventional techniques. Two filler forms (brazing paste and rod) were tested using two laser sources with different absorption properties in copper (near-infrared fibre and blue lasers). The following parameters were explored: power, exposure time, wobbling geometry, beam shaping, and clamping and surface preparation. Initial process exploration relied on qualitative analysis and visual inspection of the joints. Cross-sectional analysis, chemical etching and tensile testing were then applied to the most promising conditions. Brazing paste was found to be unsuitable as copper's conductivity drew away heat faster than it could be supplied, resulting in the lower sheet being starved of heat, while increasing the power merely damaged the upper plate. Brazing rod, by contrast, produced complete, low-porosity joints over a wide process window, especially with the near- infrared (NIR) laser. Tensile tests on selected rod-brazed specimens showed consistent peak stresses of 220-231 MPa, with fracture occurring outside the joint. This confirms that the strength matches or exceeds that of the base material. Thermal simulations, calibrated against thermosensitive sticker measurements, corroborated these results.| File | Dimensione | Formato | |
|---|---|---|---|
|
2026_10_Labate_tesi.pdf
non accessibile
Descrizione: tesi
Dimensione
34.64 MB
Formato
Adobe PDF
|
34.64 MB | Adobe PDF | Visualizza/Apri |
|
2026_10_Labate_Executive Summary.pdf
non accessibile
Descrizione: executive summary
Dimensione
2.4 MB
Formato
Adobe PDF
|
2.4 MB | Adobe PDF | Visualizza/Apri |
I documenti in POLITesi sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
https://hdl.handle.net/10589/266759