This thesis investigates the linear and non-linear structural behaviour of a cylindrical GRP silo shell, combining Abaqus finite element analysis with the buckling provisions of EN 1993-1-6 [F] and the composite-specific EN 13121-3 [L]. The work addresses a VPD17.5 silo supported not by a continuous foundation ring but by three discrete steel legs bolted to the shell wall, a configuration for which the closed-form Eurocode formulae do not directly apply. The structural response is characterized through linear elastic bifurcation (Buckle), geometrically non-linear analysis of the perfect geometry (GNA), and geometrically non-linear analysis with imperfections (GNIA), with Buckle eigenmodes scaled to EN 1993-1-6 [F] Fabrication Tolerance Quality Classes A, B and C and propagated through the modified Riks method. Five load cases (axial compression, bending, surface traction, external pressure and shear torsion) are assessed for both the idealized continuous cylinder and the actual discontinuous, legsupported geometry, against EN 1993-1-6 [F] and EN 13121-3 [L] predictions. The GRP material is characterized experimentally through fibre content, hardness, tensile, flexural and creep testing on two laminate configurations, and the steel-to-composite bolted connection at each leg is verified against CEN/TS 19101:2022 [O]. The results show that the discrete leg supports, rather than the applied imperfection, govern the shell's capacity, with GNIA returning a load capacity substantially higher than the linear, Eurocode-based verification for most load cases (bending being a notable exception in the direct GRP-code comparison), showing that the code check generally underestimates the shell's true capacity. Extending this to the complete silo under the six EN 1991-4 [D] load combinations, the wind-discharge combination (DW) governs, with demand forces remaining safely below the GNIA-assessed reserve capacity. The bolted steel-to-composite connection, however, is governed by pin-bearing failure under the current geometry, exceeding its design resistance and remaining an open point to be closed through redesign or a design-assisted-by-testing campaign.
Questa tesi indaga il comportamento strutturale lineare e non lineare di un guscio cilindrico di silo in GRP, combinando l'analisi agli elementi finiti in Abaqus con le disposizioni sull'instabilità dell'EN 1993-1-6 [F] e con la norma specifica per i compositi EN 13121-3 [L]. Il lavoro riguarda un silo VPD17.5, sostenuto non da un anello di fondazione continuo ma da tre gambe metalliche discrete imbullonate alla parete del guscio, una configurazione per cui le formule in forma chiusa degli Eurocodici non sono direttamente applicabili. La risposta strutturale viene caratterizzata tramite biforcazione elastica lineare (Buckle), analisi geometricamente non lineare sulla geometria perfetta (GNA) e analisi geometricamente non lineare con imperfezioni (GNIA), con i modi propri del passo Buckle scalati alle Classi di Qualità di Fabbricazione A, B e C dell'EN 1993-1-6 [F] e propagati tramite il metodo di Riks modificato. Cinque casi di carico (compressione assiale, flessione, trazione superficiale, pressione esterna e torsione a taglio) vengono valutati sia per il cilindro idealizzato con supporto continuo sia per la geometria discontinua realmente sostenuta dalle gambe, confrontandoli con le previsioni dell'EN 1993-1-6 [F] e dell'EN 13121-3 [L]. Il materiale GRP viene caratterizzato sperimentalmente tramite prove di contenuto di fibra, durezza, trazione, flessione e fluage su due configurazioni di laminato, e il collegamento bullonato acciaio-composito di ciascuna gamba viene verificato secondo la CEN/TS 19101:2022 [O]. I risultati mostrano che i supporti discreti delle gambe, più che l'imperfezione applicata, governano la capacità del guscio, con la GNIA che restituisce una capacità di carico sostanzialmente superiore rispetto alla verifica lineare basata sull'Eurocodice per la maggior parte dei casi di carico (con la flessione come eccezione nel confronto diretto con la normativa GRP), mostrando che la verifica del codice sottostima in generale l'effettiva capacità del guscio. Estendendo l'analisi all'intero silo sotto le sei combinazioni di carico dell'EN 1991-4 [D], la combinazione vento-scarico (DW) risulta governante, con le forze di domanda che rimangono al di sotto della riserva di capacità valutata tramite GNIA. Il collegamento bullonato acciaiocomposito, tuttavia, risulta governato dalla rottura per pin-bearing nella geometria attuale, eccedendo la propria resistenza di progetto e rimanendo un punto aperto da chiudere tramite riprogettazione o una campagna di design-assisted-by-testing
Linear and non-linear finite element analysis of GRP shells
Gressler Jardim, Alice
2025/2026
Abstract
This thesis investigates the linear and non-linear structural behaviour of a cylindrical GRP silo shell, combining Abaqus finite element analysis with the buckling provisions of EN 1993-1-6 [F] and the composite-specific EN 13121-3 [L]. The work addresses a VPD17.5 silo supported not by a continuous foundation ring but by three discrete steel legs bolted to the shell wall, a configuration for which the closed-form Eurocode formulae do not directly apply. The structural response is characterized through linear elastic bifurcation (Buckle), geometrically non-linear analysis of the perfect geometry (GNA), and geometrically non-linear analysis with imperfections (GNIA), with Buckle eigenmodes scaled to EN 1993-1-6 [F] Fabrication Tolerance Quality Classes A, B and C and propagated through the modified Riks method. Five load cases (axial compression, bending, surface traction, external pressure and shear torsion) are assessed for both the idealized continuous cylinder and the actual discontinuous, legsupported geometry, against EN 1993-1-6 [F] and EN 13121-3 [L] predictions. The GRP material is characterized experimentally through fibre content, hardness, tensile, flexural and creep testing on two laminate configurations, and the steel-to-composite bolted connection at each leg is verified against CEN/TS 19101:2022 [O]. The results show that the discrete leg supports, rather than the applied imperfection, govern the shell's capacity, with GNIA returning a load capacity substantially higher than the linear, Eurocode-based verification for most load cases (bending being a notable exception in the direct GRP-code comparison), showing that the code check generally underestimates the shell's true capacity. Extending this to the complete silo under the six EN 1991-4 [D] load combinations, the wind-discharge combination (DW) governs, with demand forces remaining safely below the GNIA-assessed reserve capacity. The bolted steel-to-composite connection, however, is governed by pin-bearing failure under the current geometry, exceeding its design resistance and remaining an open point to be closed through redesign or a design-assisted-by-testing campaign.| File | Dimensione | Formato | |
|---|---|---|---|
|
2026_10_Gressler.pdf
accessibile in internet per tutti
Dimensione
3.55 MB
Formato
Adobe PDF
|
3.55 MB | Adobe PDF | Visualizza/Apri |
I documenti in POLITesi sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
https://hdl.handle.net/10589/267002